TARGET Embedded

From Free Pascal wiki
Revision as of 14:22, 21 July 2015 by Pdbreneman (talk | contribs)
Jump to navigationJump to search

English (en) español (es) 中文(中国大陆)‎ (zh_CN) 中文(台灣)‎ (zh_TW)

The embedded target is still under development and only a few controllers are supported. Nevertheless, it's possible to create programs for embedded arm devices. The embedded target targets systems without any operating system and typically several kBs of RAM and several dozens of kB of flash. A typical target is the LPC family of NXP with popular members like the LPC2124 with 16 kB RAM and 256 kB flash using the ARM7 instruction set.

Embedded port

Status

  • best support is available in svn trunk version
  • currently only arm-embedded is supported
  • supported controllers are currently limited to certain NXP LPC, ATMEL AT91, TI Stellaris and ST STM32F10x controllers, if you're interested in support for other controllers, please subscribe to the fpc-devel mailing list and write a mail so adding the support can be discussed

ARM Embedded

Build

Get latest FPC from svn:

svn co http://svn.freepascal.org/svn/fpc/trunk fpc

Get arm-embedded binutils.

For windows, they are available at http://svn.freepascal.org/svn/fpcbuild/binaries/i386-win32. You can either checkout the whole directory with or download only arm-embedded-ar.exe, arm-embedded-as.exe, arm-embedded-ld.exe, arm-embedded-strip.exe, arm-embedded-objdump.exe and arm-embedded-objcopy.exe manually. Put these utils in a directory included in your path.

To build binutils from sources http://wiki.lazarus.freepascal.org/Binutils has instructions, for example, ./configure --target=arm-linux --prefix=/opt/embarm/ --program-prefix=arm-embedded- --disable-werror, has been known to work on binutils 2.21.1 to build the binaries in the form that the fpc target embedded build desires.

Build FPC for arm-embedded (OABI):

cd fpc
make clean buildbase installbase CROSSINSTALL=1 OS_TARGET=embedded CPU_TARGET=arm SUBARCH=armv4

This builds only the compiler and the RTL instead of the whole FPC. Because of the limited capabilities of the embedded systems supposed to be used, building all packages is not useful. However, one must be careful to avoid overwriting an existing arm compiler on the system. If this is the case, INSTALL_PREFIX should be used to install into a different directory and switch between those.

SUBARCH is required and should match your target processor, e.g.:

  • for the LPC 21xx parts which are ARM7TDMI (not to be confused with armv7!) based use SUBARCH=armv4
  • for cortex-m3 parts (stellaris, stm32, etc) use SUBARCH=armv7m
  • for cortex-m devices that support DSP extensions use SUBARCH=armv7em. The compiler does not yet support the cortex-m* FPU

Testing

Below you find a simple example program for the LPC2124 microcontroller, save it as tled1.pp to follow the description. The program is made for development boards like the LPC-WEB from OLIMEX (http://www.olimex.com/dev/lpc-e2124.html). When you press button 1, led 1 lights for a certain time, same for button 2 and led 2.

procedure Wait(d : dword);
begin
  while d<>0 do
    dec(d);
end;

begin
  { initialize PLL }
  InitPLL(2,1);

  { initialize LEDs }
  { port 0.8: output }
  TBitvector32(GPIO0_IODIR)[8]:=1;
  { port 0.10: output }
  TBitvector32(GPIO0_IODIR)[10]:=1;

  { turn off both LEDs }
  TBitvector32(GPIO0_IOSET)[8]:=1;
  TBitvector32(GPIO0_IOSET)[10]:=1;

  { initialize button inputs }
  { port 0.9: input }
  TBitvector32(GPIO0_IODIR)[9]:=0;
  { port 0.15: input }
  TBitvector32(GPIO0_IODIR)[15]:=0;

  { endless loop}
  while true do
    begin

      { button 1 pressed }
      if TBitvector32(GPIO0_IOPIN)[15]=0 then
        begin
          { turn on LED, inverse logic }
          TBitvector32(GPIO0_IOCLR)[8]:=1;
          { wait }
          Wait(500000);
          {  turn off LED, inverse logic }
          TBitvector32(GPIO0_IOSET)[8]:=1;
      end;

      { button 2 pressed }
      if TBitvector32(GPIO0_IOPIN)[9]=0 then
        begin
          { turn on LED, inverse logic }
          TBitvector32(GPIO0_IOCLR)[10]:=1;
          { wait }
          Wait(500000);
          { turn off LED, inverse logic }
          TBitvector32(GPIO0_IOSET)[10]:=1;
      end;
    end;
end.

If FPC for arm-embedded is installed as described above, the program can be compiled by

fpc -Parm -Tembedded -Wplpc2124 tled1.pp
-Parm

tells the compiler to compile for arm.

-Tembedded

tells the compiler to compile for the embedded target.

-Wplpc2124

tells the compiler to compile for the NXP LPC 2124. This has two effects: first, a unit (lpc21x4 in this case) containing the startup code and the port etc. definitions for this controller is loaded. Further, the compiler uses a linker script which fits the needs of this controller.

The result of the compiler is a .hex file which can be programmed by the NXP flash programming utility.

When using a board like the mbed (http://mbed.org) which is cortex-m3 based. Another ARM core but uses only thumb/thumb2 instructions not ARM/thumb instructions. A few subtle differences, first building fpc

make clean buildbase installbase CROSSINSTALL=1 OS_TARGET=embedded CPU_TARGET=arm SUBARCH=armv7m

Second when compiling your program

fpc -Parm -Tembedded -Wplpc1768 -Cparmv7m myprogram.pp

The -Cparmv7m option causes thumb2 code to be generated instead of the default (ARM based), probably not a bad idea to use the -Cp for processors using ARM instructions as well. -Wp as with the example above specifies the specific target, in this case microcontroller, to build for.

Adding new controllers

Adding a new controller type requires basically three steps: first, extend the compiler so it knows about the name of the controller then add a linker script and finally create an RTL unit with the register definitions and the startup code.

Add the controller type to the compiler

This is done in the file compiler/arm/cpuinfo.pas Here you need to add an identifier for the controller in the tcontrollertype enum At the same time you must update the embedded_controllers array. The array holds information about the amount of flash and sram in the controller, and what rtl unit should be included by default when compiling for that controller.

Note: Make sure the string of the two arrays are long enough to contain the strings you write

Add the linker script to the compiler

Adding a linker script consists of adding the controllertype enum identifier to the case statement in compiler/systems/t_embed.pas If this is not done the compiler will generate an internalerror

Create an RTL unit with startup code and register definitions

Creating an RTL unit means creating a unit that'll automatically be used in a project compiled for the given controller type. This unit should supply an entry point and basic initialization code. Enough to get the controller running

This unit, which must be named the same as the string written in the controllerunitstr field in the embedded_controllers array, goes into the directory rtl/embedded/arm/ where there are some examples already

After that the rtl/embedded Makefile.fpc should be modified, and rebuilt so it also builds the newly added rtl unit

Useful links

See Also