Difference between revisions of "Xtensa"

From Free Pascal wiki
(To use with QEMU)
(Build FPC)
Line 93: Line 93:
  
 
   make FPC=fpc all OVERRIDEVERSIONCHECK=1 -j "CROSSOPT=-Cfhard -Cawindowed -Tlinux" OS_TARGET=linux CPU_TARGET=xtensa
 
   make FPC=fpc all OVERRIDEVERSIONCHECK=1 -j "CROSSOPT=-Cfhard -Cawindowed -Tlinux" OS_TARGET=linux CPU_TARGET=xtensa
 +
 +
==== Test FPC ====
  
 
Create a hello world in the FPC top level directory. Compile it with:
 
Create a hello world in the FPC top level directory. Compile it with:

Revision as of 19:38, 26 April 2020

Warning-icon.png

Warning: The Xtensa support is highly experimental and prone to be broken. This description is work in progress.


So far Linux and Mac hosts only, currently most of the work concentrates on the ESP32 variant with the lx6 cores.


Xtensa-FreeRTOS

Preparations

Native stable FPC must be installed and working on the system.

Install esp-idf based on the instructions given here:

Get Started (for Stable Release)

Follow the instructions to a least step 8 where you build the hello_word demo project.

copy all the freshly compiled .a files from the current project directory to a directory of your choice:

 mkdir ~/esp/xtensa-esp32-elf-libs
 find ~/esp/ -name "*.a" -exec cp {} ~/esp/xtensa-esp32-elf-libs \; 

Notes:

  • One should not copy libraries from the project/build/bootloader directory, since these libraries do not contain full functionality.
  • Some of the required libraries are located in the esp-idf/components folder. Important to also copy the libraries in the ~/esp/esp-idf/component directory if the demo project was copied to outside the esp-idf directory.

Now you are ready to compile fpc and rtl.

execute

export IDF_PATH=~/esp/esp-idf
source ~/esp/esp-idf/export.sh

to get the path and environment set (namely tools path and $IDF_PATH are needed)

Build FPC

Change into the fpc directory and run

 make FPC=fpc CPU_TARGET=xtensa OS_TARGET=freertos "CROSSOPT=-Cplx6 -XPxtensa-esp32-elf- -Cfhard" all -j


Tips & Tricks

If linking fails due to missing libraries, you can search them by (replace missing_symbol by the missing symbol):

 xtensa-esp32-elf-objdump -t ~/esp/xtensa-esp32-elf-libs/*.a | grep 'missing_symbol\|xtensa-esp32-elf-libs'

Compile and run test program

Create a hello world program in the fpc dir and compile it with

 compiler/ppcrossxtensa -Furtl/units/xtensa-freertos/ -Tfreertos -XPxtensa-esp32-elf- -O3 -Wpesp32 -Fl~/esp/xtensa-esp32-elf-libs  -Fl~/.espressif/tools/xtensa-esp32-elf/esp-2019r2-8.2.0/xtensa-esp32-elf/xtensa-esp32-elf/lib/ hello

Get partition-table.bin and bootloader.bin from the hello_world example compiled above and copy them into the same dir as the compiled hello.bin

Flash with

 esptool.py -p /dev/ttyUSB0 -b 460800 --before default_reset --after hard_reset --chip esp32  write_flash --flash_mode dio --flash_size detect --flash_freq 40m 0x1000 bootloader.bin 0x8000 partition-table.bin 0x10000 hello.bin

Monitor the output with:

 idf_monitor.py  --port /dev/ttyUSB0 hello.elf

Note:

  • Once the bootloader and partition table has been flashed once one could also just flash the application only:
 esptool.py -p /dev/ttyUSB0 -b 460800 --before default_reset --after hard_reset --chip esp32  write_flash --flash_mode dio --flash_size detect --flash_freq 40m 0x10000 hello.bin

Xtensa-Linux

To use with QEMU

Build binutils

Get binutils-gdb sources, e.g. by

 git clone git://sourceware.org/git/binutils-gdb

Binutils 2.34 is known to work, so optionally do

 git checkout binutils-2_34

Copy https://github.com/FPK/binutils-xtensa-config/blob/master/lx6/xtensa-config.h into binutils-gdb/include to configure binutils for the CPU type support by FPC for xtensa-linux. This replaces the original file.


Configure and build binutils with

 ./configure --target=xtensa-linux --disable-gdb --disable-sim --disable-readline --disable-libdecnumber
 make -j `nproc`
 sudo make install

Build FPC

Get latest trunk and build it with:

 make FPC=fpc all OVERRIDEVERSIONCHECK=1 -j "CROSSOPT=-Cfhard -Cawindowed -Tlinux" OS_TARGET=linux CPU_TARGET=xtensa

Test FPC

Create a hello world in the FPC top level directory. Compile it with:

 compiler/ppcrossxtensa hello.pp -Tlinux -Furtl/units/xtensa-linux

Run it with:

 qemu-xtensa ./hello

Xtensa-Embedded